Cordless Curing Light Pen-type

Activating and Deactivating the Light:

► The Curing Light will enter “sleep” mode if the unit has not been used for more than 2 minute, the panel display will turn off to conserve power. If the panel display is not illuminated, simply press on/off button to bring it out of the sleep mode.

► Activate the light by pressing the on/off button on the keypad.

► Press the on/off button again to turn off (interrupt) the light before the exposure time is over.

Adjust mode and curing time for the Light:

► Always use the settings recommended by the manufacturer of the dental material when selecting the settings.

► Please refer to the above for more information of mode selection and curing time setting.

► Make sure everyone is wearing the appropriate eye protection.

Warning signal:

► If the temperature on hand piece is over 40oC, the “H” and “L” indicator will illuminate at the same time and buzzer continuously beep 5 tones and cannot turn on curing LEDs.

► If the temperature on handpiece is over 35℃, the all indicator will illuminate at the same time and buzzer continuously beep a long tone for high temperature warning.

► If the battery voltage runs low, the “L” and “Ramp up” indicator will illuminate at the same time and buzzer beep continuously 3 tones. Please place the Curing Light back into charger for recharging.

Note:

► Follow manufacturer's directions for curing times on various materials. It is better to over cure rather than insufficient cure. Over curing should not harm the restoration.

The ELiTEDENT Q6-NLG is a Pen-Type Curing Light, cordless, high-performance LED light source curing unit intended for polymerization of resin-based light cured dental materials by dental professionals. ELiTEDENT Q6-NLG incorporates two types of LEDs to achieve broad wavelength with the range of 390 to 480 nm output to polymerize virtually all the resins in the market and a high power mode to produce super fast curing effect. The relevant range both for camphorquinine (CPQ) and phenyl propanedione (PPD) containing product. Though the majority of light-curing dental materials are responsive in this range of wavelengths, it is suggested you should contact the filling material maker to make sure it before use.

The ELiTEDENT Q6-NLG is a fast-curing LED Curing Light. It emits typical light energy output at about 2,000 - 2,200 mW/cm². 3 seconds to cure most composite in the market with 2mm thickness. It also features:

► Multiple mode selection: High (fast curing), low and ramp up.

► All aluminum handpiece housing for improved durability. No more plastic to stain or crack.

► Two button easy operation.

► Quiet operation, fan-free design.

► Can be used both cordless and corded.

► Low battery warning; for urgent use, just insert power cord connector into Handpiece directly.

► Rechargeable lithium battery inside, capable of 200 x 10 sec curing cycles prior to recharging.

► Slim handpiece for most comfortable hand holding

Initial set-up

NOTE: Upon receiving the LED Curing Light, check the packaging and parts for any possible damage

that may have occurred in transit. If damage is apparent, please contact your authorized Rolence distributor from which the light was purchased.

1. Remove the contents from the shipping package. Be careful not to drop or impact the Curing Light. Choose a flat, level, sturdy surface to place the charging base on. The light is shipped in a “sleep” mode, and no timer display. To wake the unit, press the On/Off button.

2. Before using for the first time, the Curing Light must be fully charged. For the first charge, this process will take about 6 hours. Use only the power supply furnished with the light system. Attempting to use another power supply source may cause injury or damage and will void the warranty.

3. Charging indicator on charging base illuminates orange light during recharging. It will turn off automatically after battery is fully charged.

NOTE: Power indicator on charge base illuminates blue light, which indicates the charging base is well connected to power supply. If power indicator is not lit when connecting power plug to charging base, please check the outlet plug is firmly connected or not.

4. Plug the connector of the power supply into the back of the charging base. Plug the other end of the power supply into the appropriate electrical outlet. As mentioned above, wait for at least 6 hours to completely charge the light before the first use.

NOTE: Verify the line plug of the power supply plug is properly rated for your facility, and that all connections comply with safe practices and all local requirements. Always use unit in conjunction with a properly grounded outlet.

#Accessories #Curing Light #Pen-type Curing Light