Ultrasonic Scaler with Water Tank

Introduction

The Rolence ELiTEDENT® Piezoelectric System Scaler is designed for use in prophylaxis treatments periodontia, and other areas of operative dentistry. Rolence Enterprise Inc. is an ISO 13485 (2003) certified manufacturer of Ultrasonic Scalers. The product is FDA registered and compliant with EN standards.

Conformance to Standards:

Ultrasonic Scaler ELiTEDENT® PS-1 Dual / PS-1 (LED) Dual conforms to IEC60601-1-2:2001 and IEC60601-1-1:2000. The device is CE marked corresponding to European Medical Device Directive (93/42/EEC)

Supplies and Replacement Parts

Contact your local Rolence dealer to order supplies or replacement parts.

Caution: Equipment not suitable for use in the presence of flammable anesthetic mixture with air or with nitrous oxide.

Caution: US federal law restricts this device to sale by or on the order of a dental professional.

The Ultrasonic Scaler is designed for use in dentistry for the following applications:

- General Scaling (G)

Removal of supragingival calculus Removal of stains

- Endo (E)

Preparation, cleaning and irrigation of root canals Retrograde preparation of root canals

- Perio (P)

Scaling and root planning Periodontal treatments

The ELiTEDENT® Ultrasonic Scaler PS-1 Dual/PS-1 (LED) Dual voltage optional: 100V, 120V, 230V, 240V

Dimension:

Height: 23 cm

Width: 21.5 cm

Depth: 22.0 cm

Weight: 3.4 kg

Contraindications

1. Ultrasonic Scalers should not be used for restorative dental procedures involving the condensation of amalgam or porcelain. The high frequency ultrasonic oscillations may loosen the restoration.

2. This device is designed to work with ultrasonic tips compatible with EMS or Satelec system. For optimal performance please use only qualified ultrasonic tips supplied by EMS, Satelec and Rolence.

3. Please check prints on your Handpiece to identify your Handpiece fits EMS or Satelec (S) tips. Satelec tip compatible Handpiece comes with (S) mark following the 135℃ autoclave logo, while EMS tip compatible Handpiece does not have it. Incorrect tip connection could cause handpiece thread damaged permanently.

Remark: EMS® is the registered trademark of the Electro Medical Systems.

Installation Instructions

General Information

If the installation of your ELiTEDENT® Ultrasonic Scaler is performed by someone other than trained Rolence distributor personnel, care should be taken to observe the following requirements and recommendations.

Unpacking the System

Carefully unpack your ELiTEDENT® Ultrasonic Scaler and verify that all components and Accessories are included:

1. ELiTEDENT® Ultrasonic Scaler main unit with factory installed handpiece tubing.

2. Detachable AC Power Cord.

3. Foot Control Pedal.

4. 2 Liquid bottles with cap

5. Autoclavable Handpiece Set

6. Handpiece Holder with screws

7. Ultrasonic Tips and Dynamometric Wrench.

8. Spare tubing pump for replacement

9. User Direction Manual.

System Installation

1. Place the system on a level surface. Be sure unit is stable and resting on four feet.

2. Placing unit in direct sunlight may discolor plastic material.

3. Install handpiece holder on the top of main unit by fixing 2 screws.

Install liquid tanks

Insert the liquid tanks downward into the base until feeling a gentle “click”.

Rear Panel Controls / Power Connection

1. The ON/OFF Control Switch and power indicator is located on the Front Panel of the ELiTEDENT® Ultrasonic Scaler. (See Section 9.1)

2. Verify the ON/OFF Control Switch located on the front panel of the ELiTEDENT® ultrasonic scaler is in the OFF position before proceeding.

3. Plug the detachable AC Cord into the back of the ultrasonic scaler and into an approved outlet.

System Controls – Rear Panel

Handpiece Holder

Securely holds the handpiece when system is not being used.

Foot Switch Connector

Connect foot switch here, ensure it is firmly seated.

Liquid tank switch

Choose liquid source from the tanks.

Power Socket

Connect AC power cord here, ensure it is firmly seated.

Tubing pump

Drive liquid from the water tank into ultrasonic scaling system.

Installation of Ultrasonic Scaler and Handpiece

The Ultrasonic Scaler is designed to work with all EMS® or Satelec (S) tips. Please check prints on handpiece to identify which tip spec. is required. Incorrect tip connection can cause handpiece thread damaged.

Use Dynamometric Wrench to mount and drive ultrasonic instrument onto the appropriate handpiece gently. Note: The tip must be screwed and moderately tightened.

Use of Instrument

The ultrasonic instrument is for use in dentistry with Rolence® ELiTEDENT® Ultrasonic Scaler.

Rolence offers 5 different kinds of ultrasonic instruments. The longer and thinner an instrument is, the better becomes its access to periodontal pockets and inter-proximal areas. Also, at a constant power setting on the unit, a longer and thinner instrument delivers less clinical power. This means slower concrement removal and less pain for the patient. For gentle treatment, choose a very long and very thin instrument. Only switch to a shorter instrument if a particular treatment situation requires more power than the longer instrument can deliver.

The standard package of ELiTEDENT® Ultrasonic Scaler includes few tips only. To afford extra tips, please contact Rolence authorized dealer to order.