Dental Magneto Ultrasonic Scaler

Magnetostrictive Ultrasonic Scaler MS-50 features:

1. DETACHABLE HANDPIECE: Can be autoclaved in high temperature 135℃.
2. DUAL FREQUENCY: Detecting 25K and 30K insert automatically.
3. EXTERNAL FILTERS：Effectively block impurities in water, simple set up, filter can be disposable.
4. CONTROL PANEL：Simple operation, also include adjustment water volume control valve.
5. TURBO BOOST：Second position foot switch provides extra power to remove heavy calculus.

ROLENCE ENTERPRISE INC. is an ISO 9001, ISO 13485 certified manufacturer of Ultrasonic Scalers. All the products are FDA registered and compliant with EN standard (CE Marking).

Conformance to Standards:

The MS-50 R1 Ultrasonic Scaler conforms to IEC60601-1-2:2007 and IEC60601-1-1:2006. The device is CE marked corresponding to European Medical Device Directive (93/42/EEC).

CAUTION: EQUIPMENT NOT SUITABLE FOR USE IN THE PRESENCE OF FLAMMABLE

ANESTHETIC MIXTURE WITH AIR OR WITH NITROUS OXIDE.

CAUTION: U.S FEDERAL LAW RESTRICTS THIS DEVICE TO SALE BY OR ON THE ORDER OF A DENTAL PROFESSIONAL.

MS-50 R1 Ultrasonic Scaler

Voltage input: 100V, 110V, 230V, 240V

Wattage: MAX. 80 W

Water Pressure: 20 - 40 psi

Dimension:

Height: 19.5 cm

Width: 8.5 cm

Depth: 21.0 cm

Weight: 2500 g

Tip vibration frequency: 25/30 k +/- 3 kHz

Half-excursion force: < 1N

Contraindications

‧Ultrasonic Systems should not be used for restorative dental procedures involving the condensation of amalgam.

‧This Ultrasonic Scaler is designed to work with all Cavitron® (remark) 25Khz and 30Khz frequency inserts. For optimum performance please use only qualified inserts supplied by Cavitron® or ROLENCE.

‧Do not use this device if the patient or operator is wearing a pacemaker.

Remark: Cavitron® is a registered trademark of Dentsply® International, Inc

Warnings

‧Persons who are fitted with cardiac pacemakers, defibrillators and other active implanted medical devices, have been cautioned that some types of electronic equipment might interfere with the operation of the device. We recommend that the MS Handpiece Cable Set be kept at least 6 to 9 inches (15 to 23 cm) away from any device and their leads during use.

General Infection Control

Recommendations

‧As with all dental procedures, the use of standard personal protection equipment (i.e., wearing a face mask, eyewear, or face shield, gloves and protective gown) is recommended.

‧For maximal operator and patient safety, carefully follow section 12 system maintenance and care information detailed in the operating instruction.

‧As with high speed handpieces, and other dental devices, the combination of water and ultrasonic vibration from your MS-50 R1 Ultrasonic Scaler will create aerosols. With proper technique, much of the aerosol dispersion can be effectively controlled and minimized. Please carefully follow the procedural guide lines in this manual regarding the use of your Ultrasonic Scaler.

‧Always flush your MS-50 R1 Ultrasonic Scaler at least 20 seconds with highest flow after each treatment.

‧Clean and disinfect the handpiece sleeve between patients. The handpiece sleeve can be autoclaved up to 135℃ for at least 10 minutes.

Sterilizing:

1. Autoclave: compliant with standard EN 13060.

2. Place sterilizable sleeve of handpiece and pouched ultrasonic insert into a steam autoclave. After warm-up is completed, operate at a sterilizing temperature and pressure of 273° F/31 psi (134°C/216 kPa) for 18 minutes, followed by a

20-30 minute drying time.

3. To maintain sterility, the insert should remain in the sealed pouch until it is ready for use.

DO NOT USE Cold sterilization solution.

#Ultrasonic Scaler #Ultrasonic Scalers #Scaling Tip #Accessories